CCIE - ATM Switch gone very wrong.

Author

ATM Switch gone very wrong.

Quarantine

2004-07-27, 10:37 am

Hi all, I haven't been able to contribute a lot here and nor have I posted much either. AND, I'm still working on my CCNA. Yeah, I'm guilty. If you believe that I'm much too premature to be considered for any reply in a CCIE forum, you're right. But seeing how ATM is only discussed in CCIE, I wanted to see if anyone is willing to give me advice on this. Well, the situation is that I got hold of a Cisco LS1010 ATM Switch which I was told that it was "operational". I must have been spaced-out pretty good because I just bought it off, -no questions asked-. I took it home and left it around for about a week until I finally brought myself to read up on this new box. I turn it on and confirm the usual lettering floating by until I get this "Power-on Diagnostics Failed" prompt. The following is the entire script output that I got:

System Bootstrap, Version 201(1025), SOFTWARE
Copyright (c) 1986-1996 by cisco Systems
ASP processor with 16384 Kbytes of main memory

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCCCCCCCread
ing the file
into me
mory...
Self decompressing the image :
##############################
###################
##############################
##############################
################
####
##############################
### [OK]

Booting on May 28 2004 06:16:20 with 2-PAM Configuration

LS1010 Diagnostics V2.3, Dated Jan 10 1997 19:52:03
Model CPU-Card, Serial# 3825479, H/W V3.2, SWC Rev-3
Model FC1-Card, Serial# 3825635, H/W V3.2
Copyright (c) Cisco Systems Inc. 1995-1996

F.................................
Power-on Diagnostics Failed

Notice: NVRAM invalid, possibly due to write erase.
boot of "cisco2-ASP" using boot helper "bootflash:ls1010-wp-mz.111-8.bin"
failed
error returned: No usable interfaces
loadprog: error - on file open
boot: cannot load "cisco2-ASP"

System Bootstrap, Version 201(1025), SOFTWARE
Copyright (c) 1986-1996 by cisco Systems
ASP processor with 16384 Kbytes of main memory

*** Bus Error (Load) Exception ***
Access address = 0xb4e81b40
PC = 0xbfc18578, Cause = 0x1c, Status Reg = 0x30408403
DCL Masked Interrupt Register = 0x00000000
DCL Interrupt Value Register = 0x00000000

System Bootstrap, Version 201(1025), SOFTWARE
Copyright (c) 1986-1996 by cisco Systems
ASP processor with 16384 Kbytes of main memory

PCMCIA slot0 device is not initialized
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
boot: cannot open "slot0:"
boot: cannot determine first file name on device "slot0:"
E
E
Switch>sh ver
Cisco Internetwork Operating System Software
IOS (tm) PNNI Software (LS1010-WP-M), Version 11.1(8), RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-1997 by cisco Systems, Inc.
Compiled Fri 10-Jan-97 19:27 by
Image text-base: 0x600108D0, data-base: 0x6033A000

ROM: System Bootstrap, Version 201(1025), SOFTWARE

Switch uptime is 1 minute
System restarted by power-on
System image file is "bootflash:ls1010-wp-mz.111-8.bin", booted via
bootflash

cisco ASP (R4600) processor with 16384K bytes of memory.
R4600 processor, Implementation 32, Revision 2.0
Last reset from power-on
1 Ethernet/IEEE 802.3 interface.
8 ATM network interfaces.
125K bytes of non-volatile configuration memory.

8192K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102

Switch>sh hard

LS1010 named Switch, Date: 06:19:45 UTC Fri May 28 2004
Feature Card's FPGA Download Version: 10

Slot Ctrlr-Type Part No. Rev Ser No Mfg Date RMA No. Hw Vrs Tst EEP
---- ------------ ---------- -- -------- --------- -------- ------- --- ---
0/0 155MM PAM 73-1496-03 A0 02833241 Apr 18 96 00-00-00 3.1 0 2
1/0 155SM PAM 73-1505-03 A0 03824767 Sep 26 96 00-00-00 3.1 0 2
2/0 ATM Swi/Proc 73-1402-04 A0 03825479 Sep 28 96 00-00-00 3.2 0 2
2/1 FeatureCard1 73-1405-03 B0 03825635 Sep 28 96 00-00-00 3.2 0 2

DS1201 Backplane EEPROM:
Model Ver. Serial MAC-Address MAC-Size RMA RMA-Number MFG-Date
------ ---- -------- ------------ -------- --- ---------- -----------
LS1010 2 68000923 006070594E00 256 0 0 Jun 12 1996

Switch>

Atleast what I can tell for sure according to the above is that there was some kind of bus error and none of the ATM or FDDI interfaces are being recognized. I know I'm am waytoo ill-prepared for this kind of stuff but am presently (more or less hysterically) searching and reading up on this issue. If you think this is a fatal or totally undoable matter, then it would save me some time and effort to let me know. But! if this is something that can be fixed with a little more research, please let me know of anything that might help. Pointers, clues, recommendations, anything is welcome. All thanks in advance!

ZacDogg

2004-07-27, 11:15 am

I by know mean am a LS1010 expert, but it is odd...it does say there are no usable interfaces, yet your show ver shows that there is 1 ethernet and 8 ATM interfaces. Can you not see these interfaces in the config?

Zac

Sponsored Links