|
Home > Archive > CCNP > July 2003 > 2900xl switch faulty ports
You are viewing an archived Text-only version of the thread.
To view this thread in it's original format and/or if you want to reply to
this thread please [click here]
| Author |
2900xl switch faulty ports
|
|
| haseeb_eng 2003-06-04, 3:40 am |
| Before this switch was working fine . Then suddenly port 0/15 and 0/16 started showing orange lights . I had tried to reboot it but still orange light is there on these ports and network does,nt work on these ports . Other ports are working fine . Right now only 3 users are connected to this switch . Is it hardware problem of the ports ? | |
|
| It certainly sounds like it, I assume you have checked the configs for them ports and nobody has "misconfigured" it?
You could always try a wr erase and see if this fix's it, but it sounds like you need to replace it. | |
| haseeb_eng 2003-06-04, 4:02 am |
| Nothing is configured on this switch just plug and play except vlan management ip address . check THESE commandS :-
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) C2900xl Software (C2900xl-C3H2S-M), Version 12.0(5)WC5, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Tue 28-May-02 11:11 by devgoyal
Image text-base: 0x00003000, data-base: 0x0034A3C8
ROM: Bootstrap program is C2900xl boot loader
nd-swch16-m-el2 uptime is 5 days, 22 hours, 15 minutes
System returned to ROM by reload
System image file is "flash:c2900xl-c3h2s-mz.120-5.WC5.bin"
cisco WS-C2924M-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory.
Processor board ID FAA0324L0BW, with hardware revision 0x03
Last reset from warm-reset
Processor is running Enterprise Edition Software
Cluster command switch capable
Cluster member switch capable
24 FastEthernet/IEEE 802.3 interface(s)
1 Gigabit Ethernet/IEEE 802.3 interface(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00 0:BA:11:B0:00
Motherboard assembly number: 73-3425-08
Power supply part number: 34-0920-01
Motherboard serial number: FAA03229V98
Power supply serial number: NONE
Model revision number: A0
Model number: WS-C2924M-XL-A
System serial number: FAA0324L0BW
Module Ports Model HW Version SW version
------ ----- ----- ---------- ----------
1 1 WS-X2931-XL xxxx xxxx
2 4 WS-X2924-XL-V xxxx xxxx
Configuration register is 0xF
------------------ show running-config ------------------
Building configuration...
Current configuration:
!
version 12.0
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname nd-swch16-m-el2
!
enable secret 5
!
!
!
!
!
!
ip subnet-zero
!
!
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!
interface FastEthernet0/21
!
interface FastEthernet0/22
!
interface FastEthernet0/23
!
interface FastEthernet0/24
!
interface GigabitEthernet1/1
!
interface FastEthernet2/1
!
interface FastEthernet2/2
!
interface FastEthernet2/3
!
interface FastEthernet2/4
!
interface VLAN1
ip address 10.0.0.21 255.255.252.0
no ip directed-broadcast
no ip route-cache
!
snmp-server engineID local 00000009020000D0BA11B000
snmp-server community RW
snmp-server community RO
!
line con 0
transport input none
stopbits 1
line vty 0 4
password
login
line vty 5 15
password
login
!
end | |
|
| Try plugging a different device in those ports. Something that you know works. And make sure to use the right cables. If those ports are amber, they are in blocking, listening, or learning stages. So at least it is trying to establish a connection.
You could also turn port-fast on for those two ports. Port-fast skips the listening and learning stages, and imediately transitions to forwarding. Her is the command:
Switch# configure terminal
Switch(config)# interface fa0/15
Switch(config-if)# spantree start-forwarding
Do the same thing for port 16.
-capac | |
| haseeb_eng 2003-06-30, 11:36 pm |
| There was no station connected to these ports ? | |
|
| Type the following command and then post the output:
Switch# show spanning-tree
-capac |
|
|
|
|