CCNP - what could be the possible problem with this 3640 router ?

Author

what could be the possible problem with this 3640 router ?

haseeb_eng

2002-12-01, 7:36 am

in 3640 router i had installed Nm-1FE2W(1 fastethernet and 2 wan slot ) module but the router does not reongnizes it . I had checked other modules are working fine i had changed the slot also but also same problem . It seems that there is some problem with the module itself . I will paste router's reboot message and shopw version also please have a look and tell me what could be the possible problem if network module is ok .

sh ver
Router#sh version
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-DS-M), Version 12.0(5), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Wed 16-Jun-99 12:37 by phanguye
Image text-base: 0x60008918, data-base: 0x60A9C000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

Router uptime is 2 minutes
System restarted by power-on
System image file is "flash:c3640-ds-mz.120-5"

cisco 3640 (R4700) processor (revision 0x00) with 24576K/8192K bytes of memory.
Processor board ID 25129224
R4700 processor, Implementation 33, Revision 1.0
Channelized E1, Version 1.0.
MICA-6DM Firmware: CP ver 2310 - 6/3/1998, SP ver 2310 - 6/3/1998.
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
60 terminal line(s)
2 Channelized E1/PRI port(s)
--More-- DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Router#
þ
System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
C3600 processor with 32768 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled

program load complete, entry point: 0x80008000, size: 0x5b5888
Self decompressing the image : ##############################

##############################

##############################

##############################

##############################

##############################

##############################

##############################

##############################

##############################

##############################

##############################

##############################

##############################

##############################

##############################

################## [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-DS-M), Version 12.0(5), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Wed 16-Jun-99 12:37 by phanguye
Image text-base: 0x60008918, data-base: 0x60A9C000

cisco 3640 (R4700) processor (revision 0x00) with 24576K/8192K bytes of memory.
Processor board ID 25129224
R4700 processor, Implementation 33, Revision 1.0
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
60 terminal line(s)
2 Channelized E1/PRI port(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)

Press RETURN to get started!

00:00:04: %PA-2-UNDEFPA: Undefined Port Adaptor type 215 in bay 0
00:00:12: %LINK-4-NOMAC: A random default MAC address of 0000.0c8c.9224 has
been chosen. Ensure that this address is unique, or specify MAC
addresses for commands (such as 'novell routing') that allow the
use of this address as a default.
00:00:17: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-DS-M), Version 12.0(5), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Wed 16-Jun-99 12:37 by phanguye
Router>

philf

2002-12-01, 5:27 pm

The modular port adapter or service module is not recognized by the software. Use the Software Advisor to find which software version is supporting that port adapter.

http://www.cisco.com/warp/public/63/tool_links.shtml

This shows that the minimum supported software for a NM-1FE2W running on a 3600p series router is one of the following

12.0(7)XK, 12.1(1)T, 12.1(5)YB, 12.1(5)YD, 12.2(1), 12.2(2)T, 12.2(2)XT, 12.2(8)T, 12.2(11)T1

You need to upgrade the software on your router

Hope this helps

Phil

haseeb_eng

2002-12-02, 1:05 am

thanks for your reply philf. Just check in sh version command the RAM size I could'nt understand this thing why it is showing this much less ? There is more RAM installed and this is new router not old .

Sponsored Links